How to Install a Bath Tub
How to Install a Bath Tub
Blog Article
Do you find yourself in search of critical information around How to Install a Bathtub Yourself?
Setting up a tub isn't exactly rocket science, yet it does call for solid plumbing, carpentry, and also occasionally, tiling abilities. Replacing an old bathtub with a brand-new one is additionally a moderately challenging project. If the old bathtub is easily available, the project can relocate immediately; if you have to open a wall surface to eliminate the old tub and place the new bathtub, the job is a lot harder. In either situation, the project is within a residence handyman's abilities, although you will require an assistant to move out the old bathtub as well as set in the brand-new one. Make certain you have certified on your own for the job and also fit attempting it. As opposed to employing a professional to take control of a halfway-completed job, it is better to take into consideration utilizing one before you start. Chances are you might need a professional plumber to make tube links.
This short article will certainly assist you mount a brand-new bathtub in your shower room if you have currently purchased a brand-new tub and also don't require to alter the setup of your previous supply of water pipelines.
Your tools and also material list ought to consist of the following:
Removing Old Touches
If you need to replace old faucets with new ones as a part of your setup, then the first thing you must do is separate the supply of water. After doing so, activate the taps to drain pipes any type of water remaining in the system. The process of getting rid of the existing taps can be rather problematic because of the limited access that is commonly the case.
Utilize a container wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipelines to the taps. Have a fabric all set for the remaining water that will certainly originate from the pipes. When the supply pipelines have been eliminated, make use of the very same device to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the single taps from transforming throughout this process. When the faucets have actually been removed, the holes in the bath/basin will certainly need to be cleaned of any type of old securing substance.
Prior to proceeding to fit the new faucets, contrast the pipe connections on the old taps to the brand-new faucets. If the old faucets are longer than the new taps, then a shank adapter is needed for the brand-new faucets to fit.
Fitting New Taps
If the tails of the new taps are plastic, after that you will certainly require a plastic connector to prevent damages to the string. One end of the adapter fits on the plastic tail of the faucet and the other end offers a link to the current supply pipes.
If you need to fit a monobloc, then you will need minimizing couplers, which attaches the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next, position the tap in the installing opening in the bath/basin ensuring that the washers are in area in between the faucet as well as the sink. Protect the faucet in position with the supplier offered backnut. As soon as the faucet is firmly in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with regular faucet ports. The previous kind must be linked to the faucet finishes initially, tightening only by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have been connected.
Installing the Bath tub
Making use of both wood boards under its feet, put the tub in the needed setting. The wooden boards are useful in evenly spreading the weight of the bathtub over the location of the boards rather than focusing all the weight onto four small points.
The next objective is to ensure that the bath tub is leveled all round. This can be attained by examining the level and also readjusting the feet on the tub up until the spirit level reviews degree.
To set up faucets, fit the bottom of the furthest flexible tap connector to the appropriate supply pipeline by making a compression sign up with; after that do the exact same for the other tap.
Activate the water and also inspect all joints and new pipework for leakages and also tighten them if needed. Fill up the tub and also examine the overflow electrical outlet as well as the typical electrical outlet for leakages.
Lastly, fix the bathroom paneling as defined in the maker's instruction manual. Tiling and securing around the bath tub must wait up until the bathtub has actually been utilized at the very least when as this will settle it right into its final position.
Preparing for the Setup
First of all, the supporting frame supplied with the bathroom ought to be fitted (if required) according to the supplier's instructions. Next off, fit the taps or mixer to the bathtub. When suitable the tap block, it is important to see to it that if the tap comes with a plastic washing machine, it is fitted between the bathroom as well as the taps. On a plastic bathroom, it is likewise practical to fit a supporting plate under the faucets system to prevent stress on the bathtub.
Fit the adaptable tap adapters to the bottom of the two taps utilizing 2 nuts and olives (occasionally supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet through the hole in the bathroom. Use the nut provided by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bath. See to it you use every one of the provided washers.
Link the catch to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link all-time low of the overflow tube in a similar manner.The bath must now be ready to be suited its last position.
Tiling Around the Bathtub
In the area where the bath fulfills the tile, it is required to secure the accompanies a silicone rubber caulking. This is essential as the installation can move enough to fracture an inflexible seal, causing the water to permeate the wall surface in between the bathroom and the tiling, resulting in issues with wetness and possible leaks to the ceiling below.
You can pick from a selection of coloured sealants to blend in your fixtures as well as installations. They are marketed in tubes and also cartridges, and also are capable of sealing spaces as much as a width of 3mm (1/8 inch). If you have a bigger space to load, you can load it with spins of drenched newspaper or soft rope. Remember to always fill the bathtub with water before sealing, to allow for the movement experienced when the tub is in usage. The sealer can fracture fairly early if you do not consider this motion prior to securing.
Conversely, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are also easily readily available on the market. It is advisable to fit the tiles using waterproof or water-proof glue as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a keen person who reads on A Step-by-Step Guide to Installing a Bathtub, I assumed sharing that chunk was necessary. Make sure you set aside a second to distribute this blog post if you enjoyed it. Kudos for your time. Kindly stop by our website back soon.
Schedule A Service Report this page